Tag Archives: Window

Charger, Door, Front Royal Town Square, Motor Controller

Late Night Pizza

Leave a comment

Teddy and I hopped into the CitiCar for some night driving on a pizza run Friday night. With 30 minutes to spare, we headed to the town square to kill some time, only to find it was packed for a major event. Apparently we stumbled upon a political rally. I decided to execute operation “Outlaw of the Squeeze”.

The little CitiCar can fit in most places where other cars can not

The two spots in front of the portable toilets where open. I was able to park the car far enough away so that everyone still had plenty of room.

Door Windows

I took the door windows to Dixie Plate Glass & Mirror. They recommended popping out the panes. They had 50 contract orders, and wouldn’t be able to get to it until after Christmas. I went home and popped out the window panes. Unfortunately the aluminum frames cracked. There was a lot of glue on the panes, and it was difficult removing them.

Door windows with panes separated

I continued on and traced everything. I took a few measurements and brought everything back. Unfortunately they don’t carry anything that is 3/16″ thick. They order the materials in bulk for large contracts. If I could find the material myself, they could cut the parts for me. I’m having a tough time finding acrylic with safety glazing.

CitiCar sliding pane templates laid out on 22″ x 28″ white poster board
CitiCar fixed pane templates laid out on 28″ x 22″ white poster board

The car is much quieter driving without windows. It feels like I’m driving slower. All of the noise seemed to have been amplified with those windows.

I’ll need windows soon. It’s getting colder and I can’t drive in the rain anymore. Locking the vehicle while parked is pointless.

Cup Holder

The Colonel is first in line to test out the new cup holder

Drive-through restaurants weren’t really that big in the 70’s. McDonald’s opened it’s first drive-through in the year prior to my CitiCar being built. That’s why the creature comforts in my car are an ash tray and a cigarette lighter.

I went ahead and ordered some cup holders. I didn’t’ realize how oversized they were. They hang perfectly onto the defroster vents, but I’m often tilting the drink against the window to slide it down into the holder.

Charging Stations

Jack Evans Chevrolet

A CitiCar tucked next to the service center while charging

I went back to Jack Evans Chevrolet while it was staffed during my lunch break. I talked with one of the service men by the other charger to see what the guidelines were on using the charger. They just said pull up and charge.

Being in front of the garage door, it feels like the car is in the way. The charging station is in a fairly odd spot. I pushed the car as close to the wall as I could to keep it out of the way.

A CitiCar packed at a public charging station

TownePlace Suites

A penny for your thoughts

A hotel was just built outside of the city this year. It has a public charging station – but it has a fee. I was curious to walk through the process. I tried it out and was able to test charging. In my four minute experiment, I was charged a penny. I thought it would bill me for the full hour. For now, I’ll stick to the free charging station across the street from it.

I liked how the charger had a screen giving you the current status and statistics during the charging processes.

Being charged by time, rather than the amount of energy consumed seems a bit off. I’m consuming about 20% of the rate that other vehicles can consume – which means I’m paying five times more than everyone else.

100~240 Car Battery Charger

A 12v battery charger arrived that can run on between 100 and 240 volts. At this point, all of my CitiCar onboard chargers now support both standard house power and the voltages found at public chargers. Using the ST-3000 EV charger power converter, I was able to confirm that both chargers were able to charge the car when supplied with 240 volts. At this point, only the J1772 adapter is needed on the converter.

Motor Controller

Fabricating mount for motor controller in CitiCar

Most of the day was spent installing the motor controller and switches. I continued to evaluate multiple aspects of where everything would be located once the powertrain was fully replaced.

Fabricating the mounting hardware was fairly simple. A while back, I picked up four strong-tie A311 A Angles that are usually meant for fastening posts down to concrete. Part of the fun was tracing parts and drilling a mirror image by clamping two fasteners opposing each other.

The contactor switches and motor controller were fairly heavy, and caused the angles to wobble. I settled on having two separate mounts.

Forward/Reverse contactors on separate A Angles from motor controller and main contactor.

Charging CitiCar at a paid charging station
Chimney Field, Contactor Switch, Door, Motor Controller, Speedometer

Police Department

Leave a comment

National Night Out is next Tuesday. After picking up lunch at Popeyes, Teddy and I headed over to the new Front Royal police department in our CitiCar to pick up a little “Thin Blue Line” flag and a 3 watt blue light. Afterwards, we headed over to Chimney Field park.

The Blue Line flag and a blue light

I need to pick up a little inverter so I can use my bedside lamp with my car to power the light during their cruise for the event. I tried to see how to affix the flag to the car, or just put the flag itself on the radio antenna, but I wasn’t having much luck.

Red Button

Trip odometer button

In the movie, Spaceballs, Barf switched the Eagle 5 to use Secret Hyperjets on the Eagle 5 to go into hyperactive. Men in Black had a hyperdrive on their car. Hyperdrive mode was activated by a red button that allows you to drive on the ceiling of a tunnel to bypass traffic.

With a recommendation from the C-Car owners group, I swapped out the trip odometer button for a red one. It’s already been catching peoples attention quicker.

Little red trip odometer button for secret hyperjets

Door Windows

I talked a bit with my neighbor regarding the various windows on the vehicle. He repairs automotive glass, but nothing like what the CitiCar has. He had some insight regarding the blue tint on most vehicles, having a company get measurements in case the back window breaks, and what could be done about the side windows.

I called up a company he recommended. Their first response was that they don’t do curved auto-glass. They seemed pleased that I am able to pop out the side windows and bring them in. I’ll take them over later in the week. Hopefully they can pop out the acrylic panels from the frames.

Sliding windows popped out of CitiCar doors

Contactor Mounting Bracket

Mounting bracket screws are too long

The wrong mounting hardware came with the Albright SW180 main contactor switch. The bolts were too long and could not tighten any further once they pressed against the solenoid. I found a bracket kit from Arc Components Limited located in West Yorkshire, England and had the parts imported.

Albright Bracket Kit Part No 2159-047

Main contactor switch secured onto Alltrax motor controller

The mounting hardware was perfect and looked fairly similar to the hardware used on the SW202 Forward/Reverse contactor switch.

Now that the contactor switch is secured, I can start modifying some steel brackets to affix the motor controller and FNR switches onto.

As a bonus, I got a little magnet from the company to put on my refrigerator.

Refrigerator magnet from Arc Components Limited, West Yorkshire, England

Lester Charger

I’ve been talking with tech support for the Lester Summit Series II charger regarding the egg smell, high voltage, large jump in SoC, and odd estimates being off by hours.

So far, things seem like it might be normal. Problems may be due to the age of the batteries, and that the batteries should wear in after a few charge cycles. I think the estimates being off by a factor of four may be due to the low number of amp hours the batteries have. The range that I have on the CitiCar also seems to be about a quarter of what it should have if it came with the proper batteries.

Here is the data from a charging cycle along with some visual graphs.

TimeEst MinAmpsAHVoltsSoCEstimatedActual
1:1383421.1050.615%13:5403:33
1:3082720.7651.516%13:4703:16
1:4681120.41252.218%13:3103:00
2:0279520.21752.820%13:1502:44
2:2077718.32353.422%12:5702:26
2:3775918.02854.323%12:3902:09
3:0936215.83757.373%06:0201:37
3:401829.04365.290%03:0201:06
3:541699.04565.891%02:4900:52
4:041599.04665.991%02:3900:42
4:3279.05066.193%00:0700:14
4:4600.05154.6100%00:0000:00
A high voltage applied to the 48v battery bank, and an odd 50% jump in SoC within a half hour
Graph indicating estimates are four times longer than actual charging time
Door

Cruise Ship

Leave a comment

Todays trip was a quick visit to the town square. We hadn’t taken the CitiCar to Main street for a while. I saw that the store next to the ice cream shop had an eight and a half foot cruise ship made out of K’NEX called K’nector of the Seas, made by Glenn Mikulak. It’s just impressive with how large and detailed it is.

K’nector of the Seas Stern
K’nector of the Seas Bow

I found this website about Glenn and his model ship: www.glennship.com

Thick Wires

Thick 12 gauge extension cord next to a thinner extension cord

With yesterdays notice of warm wires, I headed off to the hardware store tonight and picked up the thickest gauge extension cord that I could find. I found a 50 foot heavy duty extension cord that was made of 12 gauge wires. Technically, it’s thick enough for 20 amps. As for the power strip itself, I found a three foot extension cord that was also made of 12 gauge wire, but also had a three plug splitter on the end. I am no longer worried about that wire heating up.

Scratched Window

Scratches and pitting in passenger window

The driver and passenger windows have quite a bit of pitting that’s noticeable in the right light. It’s difficult to see, but it’s something that keeps bugging me ever since I purchased the car. I’ve started looking at how to fixe the problem.

One of four knobs on the passenger door keeping the window secured

The 1976 1/2 CitiCar has four thumb-screw knobs keeping the window held in. Once they are removed, the window can be removed by pushing it out from the inside. After pushing the window out, I noticed the crack on the passenger door wraps around under the window.

Passenger door window being popped out from the CitiCar.

I unscrewed the window handle and laid the window on the garage floor. I cleaned up the window with a towel and tried to buff it with some polishing cleaner. Although the window looked cleaner, the pits and scratches remained.

Passenger door window with window handle just above it

One of the things I noticed in one corner of the non-movable pane was a label indicating the material was made of Swedcast 300 Acrylic Safety Glazing M 7 AS4. I found that SWEDCAST 300 was registered by Swedlow Inc. in Garden Grove, California

Label indicating door window material

Half of me is thinking it would be better to replace the panes with real glass or something similar to what is there now. It’s late. This repair job will continue tomorrow…